...: Epoxy is used where and how :...

Isolate and (Plated)

Wood or plywood to insulate your water, you are using thin epoxy. A brush can be used for this task, but you have to throw in the trash because the end of the brush epoksiyi navy can not solve anything. So, use the brush you can find the cheapest. If you like karina isolate large surface, you better ways to use the brush. And a sponge roller to the surface with a slight fall epoksiyi can spread. My experience is the best way to put the edge epoksiyi properly with a plastic semirigid (English squegee) by making circular movements to spread. If this work as possible between the plastic surface and formed a tight angle to make even better. Minimize unwanted air bubble formation on it. Epoxy surface how much influence will be better if your insulation is wise to the surface before sanding. This process to ensure better penetration and epoksinin and can be found on the surface of foreign substances (like oil) to allow you to get rid of. Of course, to have to clean the glass powder. Boats more than one layer of insulation are generally not recommended to be done.

Wetting

Can be used as a thin epoxy adhesive directly, even though it is preferred for the job indicated in bold epoksinin was streamlined. Just as in the insulation, adhesive bond strength in how epoksinin adhesive penetrates the surface is firmly connected. If you are directly applicable to the point bold customized epoxy adhesive, a material amount of this mixture and mix em epoksiyi will reduce the remaining amount of epoxy will weaken your ties. Therefore, before applying epoxy adhesive point bold because both the surface should be wet with epoxy thinner. Kontplak, especially the edges of plywood, epoxy em too, do not you do not forget this process. The most economical application, then wrapped in thin surface wetting epoksiyi have created, then the remaining thin kapta adhesion process of migrating to epoksiye fill in the form of making additional and bold. In case you do not do so, without freezing thick epoxy wet in parts of the application, make sure epoksiyi customized.

Fiber fiber applications

When applying epoxy thin fibers are used. Fibers of the publication, and roll or pour on a little plastic with epoxy. Between the air bubble does not stay with Fiber note plywood. If you walk towards the edge of a notice and then get rid of bubbles. Fiber epoxy to use, but enough to make it transparent, the more damage. After coming to the gel stage, but before freezing, the next time the same method applied in the solid. Fiber tape is wrapped over the putty where the application is usually a little different. Pre-publication and a roll of tape on the fresh paste with brush or your fingers to sit nicely. Air bubbles do not want, but doing so is still soft putty out of the way. Then I suggest you wait 5-10 minutes. Tape an amount from the following epoxy putty will absorb enough sucking section will be made transparent epoxy. Until you make the transparent transparent thin epoxy sections follow. Normally you can use the brush or roller. And again not to deform excessively suppressed in Macun note. Finally, look again and you find air bubbles do not destroy the mold.

Lamination

Lamination for many problems encountered in production boats to offer graceful solutions. For example, the palace or the steering D4ün as in Ballast may need a thick plywood, and you may not be available. Or, for example, may have a thick wood twisting and camber. If the thickness is not possible to give the track the desired shape, most direct solution for amateur lamination, like so many fine pieces with the thickness obtained is superimposed paste method. To clear the tracks before lamination, sanding, and remove dust and both surfaces with thin epoxy to thoroughly wet. Then one of the surface of ketchup or mayonnaise in consistency and covered with thick epoxy customized to hold each other. Torture, mass, you can use what you find. There are a few points need to be careful. The small pieces of laminated thin and long, or if thicker epoxy (mayonnaise) can use. On the other hand, large surfaces of the parts are glued to each other than consistency of a thin (ketchup) is wise to choose. This is because the air bubble to reduce the likelihood of staying. This is an important problem for the broad surface, the compressed air for the few at the top of the surface birsürü drill (a drill, Im x10cmde every 10cm). Then keep track of each other, and the hole slightly above the epoxy mixture to seep into youre comfortable. Last but very important note: Links to the holding force is not proportional press. In fact, the opposite applies. Torture and the rest are very often completely out of the epoksiyill get a weak link. Only moving part in the epoxy adhesive is not necessary to keep. As a result, do not apply too much pressure!

Pasting

Required to explain the lamination same. Locations, and fine sandpaper to clean the paste and wet with epoxy. Stay up to the desired consistency then you are epoksiyi. Do not work against gravity mayonnaise, ketchup and even temper even appropriate. Are working against gravity, not to flow epoksinin bring a little more thick is a good idea to make şokella temper. Then the area of adhesion and epoksiyi not move the parts are kept. Be careful not to more often.

To putty, and filling gaps in the surface plane

Bold parts are glued with epoxy because often when you call the stones of some will epoksinin. This section receives gushing or anything with your fingers than sticking out of the zone, distributed throughout the paste, lets call U-shaped curve (Ingilizcesi fillet). Our goal is the same as with the glass edge to leave a paste layer. Distributed over a wider area Macun load harder to make the connection. To correctly apply putty you can use your fingers (do not forget to wear gloves). To do so, spoon, or a doctor look at the persons throat when the language used to suppress the flat wooden rods are recommended. Of course, according to the scrap pieces cut and the radius you want something you can use to prepare.

For best results, the thickness of the paste, the thick-place (ie 45 degrees to port on the right) should be pasted around kontplağın thickness. Macun to the side of the correct length, the connection point for up to putty with bçlgenin edge length greater than the thickness must be pasted kontplağın (1.5 times a good choice, so the total thickness of putty is solid plywood 3). The connection of this size often allow epoxy gushing out when you do not need to add. Side in the picture "fillet" is called and shown in yellow, epoxy, paste mentioned. "filling gaps" in a moment I will be talking about the epoxy is in there with epoxy to fill gaps.

I guess what it is to fill a space, no need to explain. Future areas of work still wet on the thick epoxy personalized start. Then apply to the region and bold customized epoksiyi what is appropriate for your hands as youre passing. Flat surface (without fairing English) to fill the technical gaps as well. Deep space and surface here is not only very wide. Small dent in your car to the body shop business to smooth the putty çakiçlemeyip actually. Of course there is the option to hammer in the car, but you can not hammer on a wooden keel. To obtain a plane surface as a result, a large part of the surface to fill the remaining light dent say. Again, the wet surface with thin epoxy would start. Thick jelly into the customized application epoxy yi is wise to wait. Bold previously mentioned customized epoksiyi with plastic parts of the easiest to apply. To freeze out completely would Epoksiniz sanding. Plane for the very strong ties to the work surface to provide features not need to use filler. So easy to fill the epoksiyi thick glass can be used select ones. Connecting power of generally low filler zımparalabilen easy, hard glass high is the connecting force.

/ Favorite Paint /